Spiegelhalter

?* Informationen zur Lieferzeit

• 

  Rechteckiger Spiegel-Halter

  SURUGA SEIKI

  [Features]
  · A holder for fixing square mirrors, filters, and projection plates, etc.
  · Fix by tightening the two screws.
  · The holder is for fixing purposes only.
  · The holder is available with a width of 60 mm or 100 mm.

  CAD ：

  2D / 3D

  ab∗ ：	55.78 €
  Minimum Lieferzeit ：	5 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Spiegelhalter (optische Achse 25 mm)

  SURUGA SEIKI

  A mirror holder with an optical axis height of 25 mm. For use with the Opt Station. Select the most appropriate mounting method so that the held element does not distort when mounted. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D / 3D

  ab∗ ：	92.00 €
  Minimum Lieferzeit ：	5 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Kompaktmodell Spiegelhalter von oben bedienbar

  SURUGA SEIKI

  [Features]
  · A small top operated mirror holder with excellent stability and operability.
  · Can hold small mirrors up to ø30. The tilt can be adjusted in the two axes.
  · The tilt axis can be locked using the included lock nut.
  · The mirror can be fixed using either adhesive or via the three-point support method.
  · Types with a rod and types without a rod are available.
  · With the three-point support type, mirrors from ø20 to ø30 mm can be fixed by replacing the pins on two of the points.

  CAD ：

  2D / 3D

  ab∗ ：	122.45 €
  Minimum Lieferzeit ：	8 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Kinematischer eckiger Spiegelhalter

  CHUO PRECISION INDUSTRIAL

  [Features]
  · A three-point support type mirror holder.
  · The sample is fixed using set screws and a pad (round and square types only).
  · The set screw can be turned using a straight slot flathead screwdriver (not included).
  · For square optical devices. The tilt can be adjusted in the two axial directions.

  CAD ：

  2D

  ab∗ ：	107.88 €
  Minimum Lieferzeit ：	32 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Von oben zu bedienender Spiegelhalter mit kardanischer Aufhängung

  CHUO PRECISION INDUSTRIAL

  [Features]
  · A gimbal type mirror holder incorporating a circular mirror, in which the center of the mirror coincides with the holder's center of rotation.
  · As the tilt adjustment function is operated from the top, there is no need to worry about cutting across the optical system when making adjustments.
  · The mounting direction of the shaft can also be changed by 90°.

  CAD ：

  2D

  ab∗ ：	249.16 €
  Minimum Lieferzeit ：	23 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Kardanisch aufgehängter Spiegelhalter

  SURUGA SEIKI

  A holder for fixing items such as mirrors or plate beam splitters etc. The tilt can be adjusted in the two axial directions. The center of rotation and the center of the mirror always coincide when making fine adjustments.
  
  [Features]
  ■ F50, F55
  · Holders for fixing mirrors, plate beam splitters, and lenses, etc. The tilt (θy, θz) can be finely adjusted.
  · Fine movement of ±4° to 6° is possible, in both θy and θz, by tightening the clamp. Loosening the clamp, allows for coarse movement (adjustment) over 360°.
  · A gimbal structure in which the center of rotation and the center of the mirror always coincide when making fine or coarse adjustments.
  · The included standard rod is ø 20, and has a length of 60 mm. However the rod length can be changed. The holder's screw holes are M6P = 1. A40 to A42 rods can be used.
  · Mirror Holder F50: For the feeding method, A-type micrometer heads and an E-type screw system are available.
  · Horizontally operated type mirror holder F55: Due to the unique horizontal operation method (the operation system is installed in a horizontal direction), the user can operate it without going in front of the optical axis with their hands. A proximity specification is also available.
  ■ F52
  · A holder for fixing mirrors, plate beam splitters, and lenses, etc. The tilt (θy, θz) can be finely adjusted in the two axial directions.
  · The tilt (θy, θz) of the two axes can be finely adjusted by ±2° or ±3° (F52).
  · A gimbal structure in which the center of rotation and the center of the mirror always coincide when making fine or coarse adjustments.
  · Items such as mirrors are attached and removed using a threaded ring. Includes a resin protective ring.

  CAD ：

  2D / 3D

  ab∗ ：	169.22 €
  Minimum Lieferzeit ：	8 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Strahllenkungshalter

  SURUGA SEIKI

  [Features]
  · Types in which only the upper mirror is movable and types in which both the upper and lower mirrors are movable are available.
  · The pitch of the adjustment screw can be selected from 0.5 mm and 0.25 mm.
  · Adhesive fixing and three-point support fixing types are available for the mirror.
  · The lower side of the pole is an M16P (= 1 mm) male screw.
  · Can be fixed to magnetic bases and plates, etc.

  CAD ：

  2D / 3D

  ab∗ ：	233.07 €
  Minimum Lieferzeit ：	6 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Spiegelhalter von oben betrieben

  SURUGA SEIKI

  A top operated mirror holder with excellent stability and operability. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D / 3D

  ab∗ ：	183.31 €
  Minimum Lieferzeit ：	8 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Kompaktmodell Spiegelhalter (mit Sperre)

  SURUGA SEIKI

  [Features]
  · A holder for holding small mirrors up to ø30 mm. The tilt (θy, θz) can be adjusted in the two axes.
  · Adhesive type and three-point support type fixing are available for the mirror fixing methods.
  · With the rod-less type, M3 or M6 screws are used for fixing.
  · With the three-point support type (F58N-30-2), mirrors from ø20 to 30 mm can be held by changing the position of the lower supporting pin.
  · The fine tilt-adjustment knob is P = 0.5 mm and can be fixed to a set incline with a lock nut.

  CAD ：

  2D / 3D

  ab∗ ：	92.31 €
  Minimum Lieferzeit ：	4 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Kinematischer Rundtyp-Spiegelhalter

  CHUO PRECISION INDUSTRIAL

  [Features]
  · A three-point support type mirror holder.
  · The sample is fixed using set screws and a pad (round and square types only).
  · The set screw can be turned using a straight slot flathead screwdriver (not included). The round mirror holder is for circular optical devices. The tilt can be adjusted in the two axial directions.
  · The square mirror holder if for square optical devices. The tilt can be adjusted in the two axial directions.
  · The grooved mirror holder is for rectangular optical devices. The tilt can be adjusted in the two axial directions (square optical devices can also be used).

  CAD ：

  2D

  ab∗ ：	107.82 €
  Minimum Lieferzeit ：	33 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Rillenform-Halter

  CHUO PRECISION INDUSTRIAL

  [Features]
  · A holder for mirrors and charts, etc. Insert the corresponding item into the groove and fix in place with a clamp screw.
  · Duracon® is inserted at the tip of the clamp screw and a Teflon sheet is attached to the other side in order to avoid scratching of the clamped item.
  "Duracon®" is a registered trademark of Polyplastics Co., Ltd. in Japan and other countries.

  CAD ：

  2D

  ab∗ ：	54.51 €
  Minimum Lieferzeit ：	12 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Halbzollige Spiegelhalter

  SURUGA SEIKI

  A dedicated mirror holder for ø12.7 mm. The operation screws are available as knurled knob types that can be operated by hand, or as set bolt types which embed into equipment and are used to prevent mis-operation.
  
  [Features]
  · Has been designed from scratch with a focus on high performance and being small.
  · While the main body is of a compact size that can be installed in a space of one cubic inch, the meander width and hysteresis width of the two axes, θy and θz, have been kept to an order of just a few μrad. The stability of 60 hours (at room temperature) after positioning is the best in its class.
  · Mount using a single M4 screw. Features a step to stop rotation.
  · A mounting plate type that can be installed at 0° and 45° angles is also available.
  · When using a plate, the rod axis and the mirror reflecting surface are the same.

  CAD ：

  2D / 3D

  ab∗ ：	91.85 €
  Minimum Lieferzeit ：	8 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Spiegelhalter

  SURUGA SEIKI

  An affordable mirror holder for fixing items such as mirrors or plate beam splitters. The tilt can be finely adjusted in the two axial directions. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D / 3D

  ab∗ ：	100.49 €
  Minimum Lieferzeit ：	8 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Spiegelhalter (Schlitzklemme)

  SURUGA SEIKI

  A mirror holder with a slit-clamp type lock. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D / 3D

  ab∗ ：	122.45 €
  Minimum Lieferzeit ：	8 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Feinbewegung und Spiegelhalter in kompakter Ausführung

  SURUGA SEIKI

  A holder that can hold small mirrors up to ø30. The tilt can be adjusted in the two axes.
  
  [Features]
  · The fine-movement resolution is 0.7°/rotation, two times that of F58N.
  · Adhesive type and three-point support type fixing are available for the mirror fixing methods.
  · Both the adhesive and screw types are available with or without a rod.
  · With the rod-less type, M3 or M6 screws are used for fixing.
  · With the three-point support type, mirrors from ø20 to ø30 mm can be fixed by replacing the pins on two of the points.

  CAD ：

  2D / 3D

  ab∗ ：	92.04 €
  Minimum Lieferzeit ：	7 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Feinbewegung und Spiegelhalter in kompakter Ausführung (mit Sperre)

  SURUGA SEIKI

  [Features]
  · The FM58 with an added tilt-lock nut.
  · Adhesive type and three-point support type fixing are available for the mirror fixing methods.
  · Both the adhesive and screw types are available with or without a rod.
  · With the rod-less type, M3 or M6 screws are used for fixing.
  · With the three-point support type, mirrors from ø20 to ø30 mm can be fixed by replacing the pins on two of the points.

  CAD ：

  2D / 3D

  ab∗ ：	92.27 €
  Minimum Lieferzeit ：	4 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Präzisionsspiegelhalter (Kardanisch)

  SURUGA SEIKI

  The center of the tilt axis coincides with the mirror surface. Rearrange the plates to change to the left or right, or to a type with a vertical incidence angle of 45°. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D / 3D

  ab∗ ：	258.88 €
  Minimum Lieferzeit ：	9 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Spiegelhalter mit hoher Stabilität

  SURUGA SEIKI

  A product that is ideal for applications where a high level of precision and alignment is necessary, or where stability and operability are important. Note: The CAD data for this series is being modified. This data will be made available as soon as the modifications have been completed.

  CAD ：

  2D / 3D

  ab∗ ：	122.48 €
  Minimum Lieferzeit ：	8 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Spiegelhalter mit hoher Leistung (optische Achse: 25 mm)

  SURUGA SEIKI

  [Features]
  · A compact version of the FM532.
  · Designed with an optical axis height of 25 mm. For use with the Opt Station.
  · A product that is ideal for applications where a high level of precision and alignment is necessary, or where stability and operability are important.

  CAD ：

  2D / 3D

  ab∗ ：	99.61 €
  Minimum Lieferzeit ：	4 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Einfach-Typ Spiegelhalter

  CHUO PRECISION INDUSTRIAL

  [Features]
  · The mirror holder fixes optical devices by affixing them. As such, it can be used with both circular and rectangular shaped objects.
  · A kinematic type in which the tilt can be adjusted using the inclined fulcrum (right-top) as a guide.
  · Available with a shaft (ø8 mm, length 60 mm) or with a base plate (long hole for M6 screws).

  CAD ：

  2D

  ab∗ ：	107.44 €
  Minimum Lieferzeit ：	8 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Kinematischer Rillentyp-Spiegelhalter

  CHUO PRECISION INDUSTRIAL

  [Features]
  · A three-point support type mirror holder.
  · The set screw can be turned using a straight slot flathead screwdriver (not included).
  · For rectangular optical devices. The tilt can be adjusted in the two axial directions (square optical devices can also be used).
  · For rectangular optical devices. The tilt can be adjusted in the two axial directions (square optical devices can also be used).

  CAD ：

  2D

  ab∗ ：	107.93 €
  Minimum Lieferzeit ：	33 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Anschlussadapter mit Armhalterung

  MIRUC OPTICAL

  An arm bracket for mirror units or lenses.

  CAD ：

  2D

  ab∗ ：	52.74 €
  Minimum Lieferzeit ：	8 Arbeitstage

  *Stückpreis Standardkonfiguration

• 

  Basis-Anschlussadapter

  MIRUC OPTICAL

  A set base for arm brackets.

  CAD ：

  2D

  ab∗ ：	45.50 €
  Minimum Lieferzeit ：	8 Arbeitstage

  *Stückpreis Standardkonfiguration

Loading...